Bms own coasters....

[bigj2552]

a4 sheets x 4 coasters per sheet x 2 sheets on the press at any one time, i do these everyday of the week and will be doing upto a 1000 per week minimum in the run up to christmas my friend....just looking for a solution for you, ive always used the xpres coasters with their heat tape and like i said never had a problem with the backing

is that all ? p/t selling my friend

[paulg67]

is that all ? p/t selling my friend

thats 3 times you’ve repeated the same quote with the same reply..I didn’t say I wasn’t a part time seller, I was just replying to you saying I did more than 1 or 2 and the ones I do I’ve never had a problem with the coasters and the backing. I didn’t realise this forum was only for people who mass produce I actually thought it was for anyone to offer a bit of advice

[bigj2552]

thats 3 times you’ve repeated the same quote with the same reply..I didn’t say I wasn’t a part time seller, I was just replying to you saying I did more than 1 or 2 and the ones I do I’ve never had a problem with the coasters and the backing. I didn’t realise this forum was only for people who mass produce I actually thought it was for anyone to offer a bit of advice

good lad..nice to see someone has spare time to be very observant/picky with others posts...
but thats not really advice is it now?...thats the same spiel that others are saying with out any proof ?, incl suppliers ! - hearsay my good friend until proof is uploaded for all to see - so make vid (uncut) and let us see that you dont have any problems the rest of us have with the unisub coasters....the same thing i been asking bms to do for over 5 days now....:rolleyes:

like the other long term forum members on here, we have been using the unisub coasters for around 7/8 yr without any bother, until around 6 mths ago....and some, incl us, changed over to the bms own make of coasters, which were great until around 4/6 wks ago......same probs have arisen with those as well.....and none of the suppliers can address this problem fully at all...which is utter shocking tbh

so for all reading this thread and saying "nothing wrong here with our coasters", go make short uncut vid and post it on here, so other forum members can actually see it for themselves...otherwise its just blah blah and..blah :rolleyes:

as said earlier...comprehensive review ( incl vid ) of the souljuice coasters is coming tonight/tomorrow
note: will start fresh thread/post for that review..

[Andrew]

i have tried every dam thing - higher heat, lower heat...dont tape as hard, tape on harder...shouted, swore, danced around office none of it works ;(

for the ones who are not getting any problems with bms or unisub coasters - UPLOAD A VID OF YOU PRESSING SOME TO LET US ALL SEE WHAT/HOW YOU ARE DOING THEM.
instead of all saying...oooo they working fine for me, show us !

oooo they are still working fine but time to go taking videos at a busy time like this ain't going to happen any time soon. 2 small pieces of tape at opposite sides of coaster centres rather than corners is what we do. Both masking tape and brown heat tape would have been used and hot peel. White side up to heat plate with firm pressure. No pre-pressing or other mysterious techniques. Just straight onto paper and away to go as above.

If you want to upload a vid of what you are doing though which demonstrates the problem might be able to spot the difference then. Also gives proof that there is an actual problem rather than just hearsay and idle chatter and blah blah blah

[paulg67]

good lad..nice to see someone has spare time to be very observant/picky with others posts...
but thats not really advice is it now?...
do you practice at being patronising or does it just come natural

[technick]

Use leverage with your thumb and second finger to peel back each piece of tape. Keep the thumb on the coaster. 2000 printed in the last week around 10 rips.

[bigj2552]

oooo they are still working fine but time to go taking videos at a busy time like this ain't going to happen any time soon. 2 small pieces of tape at opposite sides of coaster centres rather than corners is what we do. Both masking tape and brown heat tape would have been used and hot peel. White side up to heat plate with firm pressure. No pre-pressing or other mysterious techniques. Just straight onto paper and away to go as above.

If you want to upload a vid of what you are doing though which demonstrates the problem might be able to spot the difference then. Also gives proof that there is an actual problem rather than just hearsay and idle chatter and blah blah blah

so what you saying is myself, and others are lying about the problems? - why would we lie about something that affects our livelihood ? that comment is just bloody stupid son - if there is no problem with the unisub coaster, then WHY does bms not upload a vid of them pressing some of these coasters to prove me wrong then ? as i have been asking them to do for nearly week now.....i, like the others who are having probs, have been using those coasters for yrs, the exact same way, with the same time/temps....nothing has changed here - 4 bits o tape at each corner..same as i/we always done it..bugger all has changed here in 7 yrs printing these things...

FOR ALL THE NEY SAYERS - UPLOAD SOME VIDS OF YOU PRESSING SOME OF THE UNISUB COASTERS...and let the ones who are having problems see once and for all that its "maybe" not the coaster at fault here, and other factors have to be brought in to consideration - but if no one uploads a dam vid to prove what they are saying ie true, then its all BS :rolleyes:

[Paul]

Is there any photo that shows the problem? I would love to see it please?

[bigj2552]

Is there any photo that shows the problem? I would love to see it please?

can do better than that paul..got vid here of the problems.....hold on...be back in tick

[Paul]

thanks... I read loads of posts about the problem but never seen one. I dont do coaster at all. maybe 5 a year for family. I still have some unisub here so could test one out....